I bought some hot-dipped galvanized nails for use in a project to build
an elevated walkway around the building shown here
<http://www.davidillig.com/observatory15.shtml>. (I'm moving the door
around to the back of the building.) I noticed right off that the
slightest off-center hammer blow would bend the nails I bought. I might
not be Tom Silva, but when I hit a nail with a hammer it usually drives
home. After too many bent nails I examined the nails. Where they bent
the zinc peeled off revealing aluminum beneath. I also noted that
hammer blows caused the nail heads to shed some zinc in nails that did
not bend.
What the ~!? I think these nails are sub-standard because they bend
easily and because the zinc can peel. They are not suitable for use in
today's pressure-treated lumber.
Comments? Experiences?
Davoud
--
usenet *at* davidillig dawt com
Davoud:
> >What the ~!? I think these nails are sub-standard because they bend
> >easily and because the zinc can peel. They are not suitable for use in
> >today's pressure-treated lumber.
B A R R Y:
> I use those for things like white vinyl siding and trim, as they won't
> ever create rust streaks.
I don't believe you would be using _these_ for that purpose; 50 or 60d
x 4-1/2 inches...
> I don't think aluminum nails were ever intended for PT wood.
Yet these were sold for that purpose!
Davoud
--
usenet *at* davidillig dawt com
Davoud:
> > I bought some hot-dipped galvanized nails ...
> > ... After too many bent nails I examined the nails. Where they bent
> > the zinc peeled off revealing aluminum beneath. I also noted that
> > hammer blows caused the nail heads to shed some zinc in nails that did
> > not bend.
dpb:
> I've never seen nor heard of galvanized Al nails -- I suspect they're
> simply a very soft steel import. What does the box say?
Only that they are hot-dip galvanized. But they are, indeed, aluminum.
> On the subject of nails I'm finding harder to get decent quality nails
> any more, even from the "real" lumber or hardware stores.
Ain't it da truth!?
Davoud
--
usenet *at* davidillig dawt com
On Thu, 05 Jun 2008 21:50:30 GMT, Davoud <[email protected]> wrote:
>What the ~!? I think these nails are sub-standard because they bend
>easily and because the zinc can peel. They are not suitable for use in
>today's pressure-treated lumber.
I use those for things like white vinyl siding and trim, as they won't
ever create rust streaks.
I don't think aluminum nails were ever intended for PT wood.
---------------------------------------------
** http://www.bburke.com/woodworking.html **
---------------------------------------------
On Jun 6, 2:53 pm, dpb <[email protected]> wrote:
> Fred the Red Shirt wrote:
> ...
>
> > ...The best metal to use
> > with AQC lumber woudl probably be bronze--very expensive.
> > Copper plated steel would be my. possibly naive, first choice.
>
> SS or double-dipped hot galvanized are the recommended choices.
>
Ah yes, 304 or 316 SS would be good too.
--
FF
On Jun 5, 7:01 pm, dpb <[email protected]> wrote:
> Davoud wrote:
> > I bought some hot-dipped galvanized nails ...
> > ... After too many bent nails I examined the nails. Where they bent
> > the zinc peeled off revealing aluminum beneath. I also noted that
> > hammer blows caused the nail heads to shed some zinc in nails that did
> > not bend.
>
> ...
>
> I've never seen nor heard of galvanized Al nails -- I suspect they're
> simply a very soft steel import. What does the box say?
>
That can be checked with a magnet.
Aluminum is amphiprotic, that means it reacts with both bases
and acids. But because it naturally forms a very tough oxide
(saphire), pure aluminum is naturally corrosion resistant
to anything that cannot penetrate that oxide layer. Concentrated
Nitric acid is routinely shipped in aluminum vessels. But dilute
nitric acid would eat through them.
Anyhow, IIRC the copper compounds used in AQC treated lumber
will eat through the oxide and corrode aluminum. But unless I
am mistaken, it eats through zinc too,. The best metal to use
with AQC lumber woudl probably be bronze--very expensive.
Copper plated steel would be my. possibly naive, first choice.
--
FF
"Davoud" <[email protected]> wrote in message
news:050620081750304644%[email protected]...
>I bought some hot-dipped galvanized nails for use in a project to build
> an elevated walkway around the building shown here
> <http://www.davidillig.com/observatory15.shtml>. (I'm moving the door
> around to the back of the building.) I noticed right off that the
> slightest off-center hammer blow would bend the nails I bought. I might
> not be Tom Silva, but when I hit a nail with a hammer it usually drives
> home. After too many bent nails I examined the nails. Where they bent
> the zinc peeled off revealing aluminum beneath. I also noted that
> hammer blows caused the nail heads to shed some zinc in nails that did
> not bend.
>
> What the ~!? I think these nails are sub-standard because they bend
> easily and because the zinc can peel. They are not suitable for use in
> today's pressure-treated lumber.
>
> Comments? Experiences?
>
> Davoud
I might have noticed that the nails are lighter weight. Is there a reason
to galvanize aluminum nails. Aluminum nails do indeed bend easily. I's say
that what you got was not what you bought.
Davoud wrote:
> What the ~!? I think these nails are sub-standard because they bend
> easily and because the zinc can peel. They are not suitable for use in
> today's pressure-treated lumber.
>
> Comments? Experiences?
From what you've said you're right, they're not suitable for use with
ACQ lumber.
Aluminum fasteners are not to be used.
Galvanized nails must meet the ASTM A-153 standard. This usually means
double hot dipped (at minimum).
--
Jack Novak
Buffalo, NY - USA
[email protected]
On Thu, 05 Jun 2008 20:02:14 -0500, dpb <[email protected]> wrote:
>Davoud wrote:
>...
>
>> I don't believe you would be using _these_ for that purpose; 50 or 60d
>> x 4-1/2 inches...
>...
>
>If Al, that sounds like a gutter nail...
I think Mr. DJB is right on the money!
---------------------------------------------
** http://www.bburke.com/woodworking.html **
---------------------------------------------
Davoud wrote:
> I bought some hot-dipped galvanized nails ...
> ... After too many bent nails I examined the nails. Where they bent
> the zinc peeled off revealing aluminum beneath. I also noted that
> hammer blows caused the nail heads to shed some zinc in nails that did
> not bend.
...
I've never seen nor heard of galvanized Al nails -- I suspect they're
simply a very soft steel import. What does the box say?
On the subject of nails I'm finding harder to get decent quality nails
any more, even from the "real" lumber or hardware stores.
--
Davoud wrote:
...
> I don't believe you would be using _these_ for that purpose; 50 or 60d
> x 4-1/2 inches...
...
If Al, that sounds like a gutter nail...what the heck are you nailing w/
them?
A google found what I knew of--galvanized Al panel stock, but nary a
single hit of "galvanized" in combination w/ "Al" and "nail" except
where both Al and galvanized nails were referenced.
--